1、ply.D. Maintain the products in a dry condition during delivery, storage, handling, installation, and concealment. E. Protect from damage from sunlight, weather, excessive temperatures and construction operations.F. Remove damaged material from the site and dispose of in accordance with applicable r
2、egulations.G. Sequence deliveries to avoid delays, but minimize on-site storage.H. Store underlayment rolls on end, on pallets or other raised surfaces. Do not double stack rolls. Cover rolled goods with breathable type covering such as tarpaulin. Visqueen or other non-breathable plastic wraps are n
3、ot acceptable.I. Handle, store, and place roofing materials in a manner to avoid significant or permanent damage to roof deck or structural supporting members.1.10 PROJECT CONDITIONSA. Perform work only when existing and forecasted weather conditions are within the limits established by the manufact
4、urer of the materials and products used.B. Proceed with installation only when substrate construction and preparation work is complete and in condition to receive waterproofing.Stanford University Facilities Design GuidelinesFebruary 2014 Page 5 of 14 2019 FDG Section 07 32 13.02C. Construction may
5、not be as shown on the Drawings and some modification of details may be required to accomplish the intent of the documents. Contractor shall receive approval in writing from Architect for all modifications or adjustments before commencing with the work.1.11 WARRANTYA. Tile Manufacturers Warranty: St
6、andard form in which manufacturer agrees to repair or replace clay roof tiles that fail in materials within specified warranty period.Note to Specifier: Verify available warranty periods for clay roof tiles with manufacturers and revise number in subparagraph below as required.1. Materials-Only Warr
7、anty Period: 75 years from date of Substantial Completion.B. Underlayment Manufacturers Warranty: Underlayment manufacturers standard warranty for manufacturers membrane and accessory products covering defects in materials.Note to Specifier: Verify available warranty periods for underlayment with ma
8、nufacturers and revise number in subparagraph below as required.1. Materials-Only Warranty Period: 10 years from date of Substantial Completion.C. Installers Warranty: Roofing Installers Warranty signed by roofing Installer, covering Work of this Section, in which roofing Installer agrees to repair
9、or replace components of roofing that fail in materials or workmanship within the following warranty period:1. Warranty Period: Five years from date of Substantial Completion.PART 2 - PRODUCTS2.1 MANUFACTURERSA. Basis-of-Design Manufacturer: Subject to compliance with requirements, provide products
10、by one of the following or approved equal:1. Clay Tile: Subject to compliance with requirements, provide 2 piece Cordova clay roof tile by Gladding McBean or approved equal.2. Tile Fasteners, Wind Lock Nose Hooks polyisobutylene plasticized; heavy bodied.Note to Specifier: Revise first paragraph bel
11、ow if elastomeric sealant of another type, grade, class, and a specific use related to substrate is required.C. Elastomeric Sealant: ASTM C 920, elastomeric polyurethane-based joint sealant; Type S, Grade NS, Class 25, Use NT related to exposure, and, as applicable to joint substrates indicated, Use
12、 O.D. Roofing Asphalt: ASTM D 312, Type IV.E. Foam Adhesive: Two-component, polyurethane expanding adhesive recommended for application by clay roof tile manufacturer.F. Mortar: ASTM C 270, Type M, with ASTM C 979, pigmented mortar matching existing color exposed-to-view mortar, and natural color fo
13、r concealed-from-view mortar as weather block at hips ridges and transitions.G. Eave Closure: Match existing characteristics including, but not limited to, material, size, color and shape.H. Tile Vents and Eave Closures: Manufacturers recommended non-corroding screen vents and solid eave closures as
14、 required for application. Match existing characteristics including, but not limited to, material, size, color and shape.Note to Specifier: Retain first paragraph below if above-deck wood components are required. Insert material requirements if preferred.I. Wood Nailers, Shims: Construction heart re
15、dwood.J. Wormgear Clamp: Type 316 stainless steel wormgear clamp.K. Accessory Products: Provide accessory products indicated in the Contract Documents and as required by the manufacturer for a complete roofing installation.Stanford University Facilities Design GuidelinesFebruary 2014 Page 7 of 14 20
16、19 FDG Section 07 32 13.022.4 FASTENERSA. Roofing Nails: ASTM F 1667, hot-dip galvanized-steel, 0.1055-inch- diameter shank, sharp-pointed, conventional roofing nails with ring shanks; minimum 3/8-inch- diameter head; of sufficient length to penetrate 3/4 inch into wood.1. Where nails are in contact
17、 with metal flashing, use nails made from same metal as flashing.B. Wire Ties: Stainless steel, 0.083-inch minimum diameter.C. Twisted-Wire-Tie System: Continuously twisted, two-wire unit with loops formed 6 inches apart, minimum 0.083-inch- diameter stainless-steel wire and 0.037-inch- diameter sta
18、inless-steel tie wires conforming to ASTM A580, with matching-metal folding clip deck anchors.1. Wood Deck Anchor: Stainless steel wood deck anchors, fastened with 2 No. 10 gauge Stainless steel ring shank nails.2. Concrete Deck Anchor: Stainless steel double-plate anchor assembly with stainless ste
19、el compression spike.Note to Specifier: Use hook nails, also called “wind locks,“ in high-wind areas and on roofs steeper than 7:12.D. Wind Lock Nose Hook: Hot-dip galvanized-steel, 0.09-inch diameter wire device designed to secure butt edges of overlaid clay roof tiles. For hip and ridge trim tiles
20、.2.5 UNDERLAYMENT MATERIALSA. Self-Adhering Underlayment: ASTM D 1970, min. of 30 mils thick; slip-resisting, high temperature-rated, polyethylene-film-reinforced top surface laminated to butyl rubber adhesive or rubberized asphalt, with release-paper backing; cold applied.1. Products: Subject to co
21、mpliance with requirements, provide products by one of the following:a. Grace Ultra; Grace Construction Products b. WIP 300HT; Carlisle Coatings ASTM D412.c. Elongation: 250 percent minimum; ASTM D412.d. Low Temperature Flexibility: Unaffected at -20 degrees F; ASTM D1970.B. Self-Adhering Flashing:
22、Same product as self-adhering underlayment.C. Primer: Manufacturers standard primer for each substrate.Stanford University Facilities Design GuidelinesFebruary 2014 Page 8 of 14 2019 FDG Section 07 32 13.022.6 METAL FLASHING AND TRIMA. General: Comply with requirements in Section 07 60 00 “Flashing
23、and Sheet Metal.“B. Fabricate sheet metal flashing and trim to comply with recommendations that apply to design, dimensions, metal, and other characteristics of the item in SMACNAs “Architectural Sheet Metal Manual“ and TRI/WSRCAs “Concrete and Clay Roof Tile Design Criteria Installation Manual for
24、Moderate Climate R罏罏.2.1设备投资占比24.88%2.1.3其它投资万元3106.942.1.3.1其它投资占比25.12%2.1.4固定资产投资占比78.37%2.2流动资金万元2675.142.2.1流动资金占比21.63%3收入万元18323.004总成本万元14619.225利润总额万元3703.786净利润万元2777.847所得税万元1.098增值税万元510.879税金及附加万元210.2310纳税总额万元1647.0511利税总额万元4424.8812投资利润率29.94%13投资利税率35.77%14投资回报率22.46%15回收期年5.9516设备数量
25、台（套）10117年用电量千瓦时596005.9518年用水量立方米17602.8419总能耗吨标准煤74.7520节能率20.56%21节能量吨标准煤23.6122员工数量人372U.S. Departmentof TransportationFederal AviationAdministrationAdvisoryCircularSubject: SUBMITTING THE AIRPORT MASTER RECORD IN ORDER TO ACTIVATE A NEW AIRPORTDate: 09/23/2010Initiated by: AAS-100AC No: 150/520
26、0-35AChange: 1. PURPOSE.This Advisory Circular (AC) provides guidelines on providing airport data to the Federal Aviation Administration (FAA) using FAA Forms 5010-3 and 5010-5. 2. CANCELLATION.This AC cancels AC 150/5200-35, Submitting the Airport Master Record in Order to Activate a New Airport, d
27、ated May 20, 2004.3. APPLICATION.This revision applies to the proponents of new civil and joint-use public-use airports and new civil private-use airports, and to FAA Regional Airports and Airports District Office (ADO) personnel, and FAA, state and contractor airport inspectors. 4. AVAILABILITY.Thi
28、s AC is available on the FAA website at www.faa.gov. 5. BACKGROUND.The FAA is authorized under Title 49 United States Code 47130, Airport Safety Data Collection, to collect, maintain, and disseminate accurate, complete, and timely airport data for the safe and efficient movement of people and goods
29、through air transportation. The FAA accomplishes this through the Airport Safety Data Program, which is the FAAs primary means for gathering aeronautical information on landing facilities.This AC is organized to reduce the burden of correctly completing and submitting Forms 5010-3 and 5010-5 to the
30、FAA.a. Chapter 1 explains some of the terms found in this Advisory Circular.b. Chapter 2 describes all four versions of FAA Form 5010, Airport Master Record.c. Chapter 3 provides information to the proponents of planned or newly established airports.AC 150/5200-35A 09/23/2010iid. Chapter 4 provides
31、a description of the data elements, the appropriate entries, and instructions for completing Form 5010. e. Appendix A includes Form 5010-3 for civil public-use airports.f. Appendix B includes Form 5010-5 for civil private-use airports.g. Appendix C provides a list of the references used in this AC.M
32、ichael J. ODonnellDirector, Office of Airport Safety and Standards09/23/2010 AC 150/5200-35AiiiTable of ContentsChapter 1. Explanation of Terms .1Chapter 2. Airport Master Records .5Chapter 3. Newly Established Airports.7Chapter 4. Data Elements.9Appendix A. FAA Form 5010-3 .37Appendix B. FAA Form 5010-5 .
个人主页
