1、.for Main Engine1 Please check the alignment of the shafting.2 Please check the alignment of M/E.3 Please check and accept the crankshaft deflection.4 Approval of force measurement of M.E. through bolts.5 Approval of the installation of fitted bolts.6 Approval of the fitted bolt holes.7 Approval of
2、force measurement of intermediate shaft.8 Approval of intermediate bearing clearance.9 The alignment of M/E is incorrect.10 The alignment of shafting is incorrect.11 The crankshaft deflection is over the allowance.12 Please make an adjustment.13 Explosive Pressure on M/E.14 The BHP( brake horse powe
3、r ) of M/E15 The torsional force of M/E.16 M.E. side support.17 M.E. stern support18 M.E. fastening support19 Start main engine20 Start M/E reversely21 Exhaust temperature is too high (low).22 Explosive pressure on M/E is too high(low).23 The temperature of the cooling water is too high (lo
4、w).24 The pressure of starting air is too low.25 The pressure of lub oil is too low.26 The pressure o scanvage air is too low.27 The rpm of turbocharger is too low.28 Start (Stop) the main starting valve.29 Start (Stop) the main L.O. pump.30 Start the auxiliary (anx.) blower.31 Start the main sea wa
5、ter cooling pump.32 Preheat the M/E cylinder.33 Preheat the L.O. circulating pump.34 Start (Stop) the F.O. circulating pump.35 Start (Stop) the F.O. supply pump.36 The pressure of F.O. is high (low).37 The F.O. pressure adjusting valve doesnt work.38 Change from light oil to heavy oil.39 M/E startin
6、g (reversing) test.40 Test of emergency stop.41 The engine control room control (the control from the control room)42 Local control43 The remote control from the bridge.44 Protection test of M/E flywheel trip.45 Shut-down test of F/W. high temp.46 Shut-down test of L.O. low press.47 Tooth sector of
7、high pressure oil pump.48 The advance angle is too large (small).49 The atomization of nozzle is too poor.50 The pressure of nozzle is too high (low).51 The nozzle leakage.52 The protection test of turning gear clutch.53 The governor has failed.54 Hydraulic chain tightener.55 The cylinder cover star
8、ting valve.56 The cylinder cover starting valve is too hot.57 The cylinder cover starting valve leakage.58 The cylinder oil one-way valve leakage.59 The cylinder oil one-way valve is fitted reversely.60() The inlet cylinder oil is too much (little).61 Cylinder score62 Cylinder seizing63 Cylinder kno
9、cking64 Poor combustion65 The exhaust gas is with water vapour.66 The exhaust gas is blacklight blue.67 Exhaust pipe vibration (leakage).68 Attached bracket of exhaust pipe.69 The bracket of exhaust pipe.70 The cooling water pipe leakage.71 L.O pipe leakage.72( / ) The Oil panThe circulatin
10、g L.O. tank / The inside of M/E is not clean.73 The M/E oil outlets are blocked.74 The safety of inner screw of M/E is not fitted properly.75 M.E. through bolt submission.76 M.E bottom fastening bolt submission.77 The L.O. (F.O.) filter doesnt work.for diesel engine generator1 The cleanness
11、 inside the main generator to be confirmed.2 The main generator crankshaft deflection to be confirmed.3 The installation of main generator to be confirmed.4 The protection of flywheel trip to be confirmed.5 The auto-stop function of L.O. low pressure to be confirmed.6 The auto-shop function of F.W.
12、high temperature to be confirmed.7 The load test of main generator.8100 100 load test of generator.9/ Instant load/ unload test of governor.1010050 100 to 50% instant unload test.1150 50 to nil instant unload test.12100 Nil to 50% instant load test.13 The parallel test of generators.14 The measureme
13、nt of thermal deflection (exterior pressure).15 The load test of emergency generator.16 The protection test of flywheel trip of emergency generator. 17 The auto-stop test of emergency generator F.W. high-temp.18 The auto-stop test of emergency generator L.O. low-press.19 The instant load & unload te
14、st of emergency generator governor.20 The parallel of emergency and main generators.for air compressor and air system1 The air compressor washer to be confirmed.2 The alignment of air compressor to be confirmed.3 Alarm test of F.W. high temperature.4 Alarm test of L.O. low pressure.5 The safety valv
15、e to be submitted.6 The filling test of air compressor.7() High-pressure (Low- pressure) auto-stop test of air compressor.8 Gas tightness submission of main air reservoir.9 The main air reservoir safety valve to be submitted10 Test of control air pressure-reducing valve.11 Gas tightness test of cont
16、rol air reservoir.12 The safety valve test of control air bottle.13 The effect test of dehumidifier.14 The test of service air pressure-reducing valve.15 The gas tightness test of service air reservoir.16 The safety valve of service air reservoir to be confirmed.17 The gas tightness test of aux. air
17、 reservoir.18 The aux. air bottle safety valve to be submitted.19 The safety valve test of emergency air compressor.20 The filling test of emergency air compressor. for boiler1 The tightness test of main boiler.2 Boiler pickling().3 The inside cleanness to be checked.4 The running test of boiler wat
18、er-feed pump.5 The vacuum testthe auto-shifting testof water-feed pump.6 The auto water-feed system to be confirmed.7 The safety valve of boiler F.O. pump to be submitted.8 The vacuum test of boiler F.O. pump.9 The auto-shifting test of boiler F.O. pump.10 The boiler safety valve to be confirmed.11
19、The test of boiler evaporation.12 The automation test of boiler.for shafting and steering gear system1 Please check the lighting target.2() Please check the alignment of shaftingsteering gear system.3 Please check the shaft hole.4磨 Please check the boring sizecleanness.5 The stern tube liner tighten
20、ness to be approved.6 The propeller impeller tightenness to be approved.7 Please check the rudder nil position.837 Port (Starboard) 37. Delivery expression for flushing1 The flushing submission.2 The oil temperature is too low.3 Vibrator installation.4 The oil is not clean.5 The oil is with particle
21、s.6 The oil is with slag.7 One more hour flushing.8 Please make it better.for underwater equipment1 The tightness test of hull valve.2 The tightness test of inlet valve for emergency fire pump.3 The tightness test of flushing valvevent valve.4() The tightness test of foremid-shipdraft valve.5 The ti
22、ghtness test of sounderlog.6 The seam is not good. Please reweld it.7 The seam is not smooth. Please grind it.8 Air leakage9 Please open the valve. for anchor windlass1 Please check the windlass washer.2 Please check the alignment of shafting.3Please check the windlass attached bracket.4 Th
23、e pressure of hydraulic pump is too high (low).5 The oil motor pressure is too high (low).6 The hydraulic oil temperature is high.7 The cooling water temperature is high.8 To clean the anchor windlasshydraulic pump.9 Please inspect the oil tanks.10The testing time is up.11 Theres a failure (Its abno
24、rmal).12 It doesnt work.13 The vibration is violent.14 The decibel() is too high (The noise is too loud).15 Too much/too little clearance.16 Overload17 too fast18 Please open the hydraulic pump cover.19 Please dismantle the cooler.20 Add a thermometer.21 Add a working platform.22 Add pipe fixed supp
25、orts.23 Please change hydraulic oil.24 Please renew L.O.25 Please discharge air.26 No load test of anchor windlass.27 Anchoring test.28 Add some grease.29 To renew the pressure gauge.30 To strengthen the engine seat.31 To lubricate the brake threads.32 Add some grease to clutchgears.33 Renew the oil
26、 nozzle.34 To adjust the brake clearance.35 Please check the anchor winch washers.36 Anchor winch bearing clearance.37 Anchor winch attached bracket.38 To clean the anchor winch.39粻 The washer size is wrong.40 The thickness of washers is too thin.41 No-load test.42 Pull test.43 Constant expansion te
27、st.44The anchor doesnt fit the side plate well.45 The anchor hasnt been lowered enough.46 ManualMechanicalanchoring.47 The bearing temperature is high.48 The hydraulic pump is too hot.49 The alignment is incorrect.50 The anchor hasnt been retaken enough.51 The installation of chain stopper to be acc
28、epted.52𣨷 RetakeLowerthe anchor. 53 RetakeLowerthe rope. (for steering gear)1 Please check the washers of steering gear.2 Please check the steering gear side bracket.3 The installation size of steering gear.4 Nil position of steering gear.51 Safety valve for steering gearNO.1 cylinder.6 The
29、pressure is too high (low).7 The rudder angle is out of control.8 Low oil level alarm.9 Oil leakage.10綯 Add some grease to motor.11 () Manualautosteering.12 Steering by single (twin) pump.13 The alignment of pump set to be approved.14 Pull rod bending.15 Grease pump leakage.16 The thermometer is loo
30、sened.17 The pressure gauge is damaged.180 ()35 Nil to port (starboard) 35.193535 Port 35 to starboard 35.1 The strength test for davitlife-boat.2 boat retakinglowering.3 boat lowering by remote control.4 Unhook automatically.5 Do it once again.6 The limiting switch of the appliance doesnt work.7 Th
31、e limiting switch of the appliance is not synchronous.8 Adjust the limiting switch of the appliance.9 The two-stage boat lifter doesnt start successfully.10 Please start.11 Strengthen the davit from underside.12 The safety lever is not flexible.13 Make an adjustment.14 Shaft tunnel oil leakage. .糵 f
32、or gangway, pilot ladder, rope ladder, derrick, blower etc.1 The strength test for gangwaypilot ladder.2 / The operating test for pilot ladderpilot ladder / pilot rope ladder.3 To install the handrails.4 Rope ladder winch.5 Full (No)-load.6 The no load ( strength) test for derrick.7 The safety valve
33、 test.8 The limiting switch test.9 / The strength test for rubbish derrickcargo derrick /hose derrick.10 The operating test for rubbish derrick.11 The safety equipment test for cargo derrick.12 The running testThe limiting switch testfor cargo derrick.13CO2 The CO2 tightness (operation) test.14 Plea
34、se put on the nameplates.15 The blower bearing is too hot.16 Poor maneuverability.17 Make an adjustment.18 Add some lub oil.19 To submit it in the morningafternoon. (for other items)1 The vacuum of pump to be confirmed.2 The pump pressure to be confirmed.3 The auto-shifting function of pumps to be confirmed.4 / The effect test of F.O. purifierD.O. purifier / L.O. purifier.5 The effect test of bilge separatorincinerator.6 The effect test of fire pumpemergency fire pump.7 The running test of service F.W (S.W).8 The running test of vapor pipes.9 The tightness test for high-pressure air pipes.
个人主页
