轮机英语(2).txt
《轮机英语(2).txt》由会员分享,可在线阅读,更多相关《轮机英语(2).txt(10页珍藏版)》请在文库网上搜索。
1、.for Main Engine1 Please check the alignment of the shafting.2 Please check the alignment of M/E.3 Please check and accept the crankshaft deflection.4 Approval of force measurement of M.E. through bolts.5 Approval of the installation of fitted bolts.6 Approval of the fitted bolt holes.7 Approval of
2、force measurement of intermediate shaft.8 Approval of intermediate bearing clearance.9 The alignment of M/E is incorrect.10 The alignment of shafting is incorrect.11 The crankshaft deflection is over the allowance.12 Please make an adjustment.13 Explosive Pressure on M/E.14 The BHP( brake horse powe
3、r ) of M/E15 The torsional force of M/E.16 M.E. side support.17 M.E. stern support18 M.E. fastening support19 Start main engine20 Start M/E reversely21 Exhaust temperature is too high (low).22 Explosive pressure on M/E is too high(low).23 The temperature of the cooling water is too high (lo
4、w).24 The pressure of starting air is too low.25 The pressure of lub oil is too low.26 The pressure o scanvage air is too low.27 The rpm of turbocharger is too low.28 Start (Stop) the main starting valve.29 Start (Stop) the main L.O. pump.30 Start the auxiliary (anx.) blower.31 Start the main sea wa
5、ter cooling pump.32 Preheat the M/E cylinder.33 Preheat the L.O. circulating pump.34 Start (Stop) the F.O. circulating pump.35 Start (Stop) the F.O. supply pump.36 The pressure of F.O. is high (low).37 The F.O. pressure adjusting valve doesnt work.38 Change from light oil to heavy oil.39 M/E startin
6、g (reversing) test.40 Test of emergency stop.41 The engine control room control (the control from the control room)42 Local control43 The remote control from the bridge.44 Protection test of M/E flywheel trip.45 Shut-down test of F/W. high temp.46 Shut-down test of L.O. low press.47 Tooth sector of
7、high pressure oil pump.48 The advance angle is too large (small).49 The atomization of nozzle is too poor.50 The pressure of nozzle is too high (low).51 The nozzle leakage.52 The protection test of turning gear clutch.53 The governor has failed.54 Hydraulic chain tightener.55 The cylinder cover star
8、ting valve.56 The cylinder cover starting valve is too hot.57 The cylinder cover starting valve leakage.58 The cylinder oil one-way valve leakage.59 The cylinder oil one-way valve is fitted reversely.60() The inlet cylinder oil is too much (little).61 Cylinder score62 Cylinder seizing63 Cylinder kno
9、cking64 Poor combustion65 The exhaust gas is with water vapour.66 The exhaust gas is blacklight blue.67 Exhaust pipe vibration (leakage).68 Attached bracket of exhaust pipe.69 The bracket of exhaust pipe.70 The cooling water pipe leakage.71 L.O pipe leakage.72( / ) The Oil panThe circulatin
10、g L.O. tank / The inside of M/E is not clean.73 The M/E oil outlets are blocked.74 The safety of inner screw of M/E is not fitted properly.75 M.E. through bolt submission.76 M.E bottom fastening bolt submission.77 The L.O. (F.O.) filter doesnt work.for diesel engine generator1 The cleanness
11、 inside the main generator to be confirmed.2 The main generator crankshaft deflection to be confirmed.3 The installation of main generator to be confirmed.4 The protection of flywheel trip to be confirmed.5 The auto-stop function of L.O. low pressure to be confirmed.6 The auto-shop function of F.W.
12、high temperature to be confirmed.7 The load test of main generator.8100 100 load test of generator.9/ Instant load/ unload test of governor.1010050 100 to 50% instant unload test.1150 50 to nil instant unload test.12100 Nil to 50% instant load test.13 The parallel test of generators.14 The measureme
13、nt of thermal deflection (exterior pressure).15 The load test of emergency generator.16 The protection test of flywheel trip of emergency generator. 17 The auto-stop test of emergency generator F.W. high-temp.18 The auto-stop test of emergency generator L.O. low-press.19 The instant load & unload te
14、st of emergency generator governor.20 The parallel of emergency and main generators.for air compressor and air system1 The air compressor washer to be confirmed.2 The alignment of air compressor to be confirmed.3 Alarm test of F.W. high temperature.4 Alarm test of L.O. low pressure.5 The safety valv
15、e to be submitted.6 The filling test of air compressor.7() High-pressure (Low- pressure) auto-stop test of air compressor.8 Gas tightness submission of main air reservoir.9 The main air reservoir safety valve to be submitted10 Test of control air pressure-reducing valve.11 Gas tightness test of cont
16、rol air reservoir.12 The safety valve test of control air bottle.13 The effect test of dehumidifier.14 The test of service air pressure-reducing valve.15 The gas tightness test of service air reservoir.16 The safety valve of service air reservoir to be confirmed.17 The gas tightness test of aux. air
17、 reservoir.18 The aux. air bottle safety valve to be submitted.19 The safety valve test of emergency air compressor.20 The filling test of emergency air compressor. for boiler1 The tightness test of main boiler.2 Boiler pickling().3 The inside cleanness to be checked.4 The running test of boiler wat
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 轮机 英语