《WEDM 线割作业规范作业规范.doc》由会员分享,可在线阅读,更多相关《WEDM 线割作业规范作业规范.doc(4页珍藏版)》请在文库网上搜索。
1、QUALITY SYSTEMS PROCEDUREWEDM Work Instruction放电机作业规范 IQP: PSC-940Page: 4 of 4Issued: 1-11-20101.0 PURPOSE 目的Define the WEDM operation instruction. 详细说明CNC 操作规范。2.0 SCOPE 范围WEDM operation shall be operated in accordance with this procedure.WEDM 操作需依照本规程.3.0 DEPARTMENT: 涉及部门Tooling department 模具部Qual
2、ity System 质量体系4.0 CONTENT 内容4.1 ObjectStandardize the WEDM process for plate.模板线割标准程序。 4.2 ScopeWEDM Work procedure线割作业程序。EquipmentMachine: Makino U32K, UP32j设备: Makino U32K, UP32jWire: OKI 0B-32PZN线:OKI 0B-32PZNClamp system: 3R system夹紧机构:3RDielectric: Distilled Water电解质: 蒸馏水 Working requirementCh
3、eck the identify of plate with the drawing.Ensure plate is same as the design drawing 确认模板跟设计图纸一致。Check the size of outside and layoutIf the layout is different with drawing, call the designer to confirm the validity.如果layout 不同于图纸,请通知设计人员确认。Check the programThe WEDM program is same as the design dr
4、awing before wire cutting. If any doubt, check with the designer immediately线切割加工程序符合图纸设计。如有任何疑问,与设计师检查Check the machine and machining conditionCheck if the wire is enough to cut this plate. Do not replace the wire in one line cut as far as possible. 在线割一块板时候尽可能不换线。Check the condition of machine is
5、good status. Confirm no problem then start working.确保机器运行状况良好,确认没有问题。Inspection equipmentDaily work日常工作According to the point inspection form fill form, such as Clean tank. Clean all parts in contact with dielectric. Empty the used wire in container on time. Check the conductivity of the dielectric.
6、 按照设备检点表认真填写相应点检项目,如:水箱清洁工作。清洁与介质接触的所有部件。倒空的容器中使用的线。检查介质导电性。Calibrate the machine校正。Operating method:First of all, check the parallelism of plate and make sure it less than 0.002mm.首先,检查模板平行度并使其小于0.002mm。Set up properly plate on the machine; clamp the plate with 3R system.建立正确的的板面,用3R系统加紧板面。Check th
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
50000 文币 0人已下载
下载 | 加入VIP,免费下载 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- WEDM 线割作业规范作业规范 作业 规范